H.-Å.Haggblad, P.Doremus and D.Bouvard: "An international research program on the mechanics of powder metal forming", Advances in Powder Metall. & Particulate Materials, Vol.2, Part 7, (compiled by T.M.Cadle & K.S.Narasimhan) MPIF, Princeton, (1996)179-192.
J.Kergadallan, G.Puente, P.Doremus and E.Pavier: "Compression of an axisymetric part with an instrumented press", Proc. Int. Workshop on Modelling of Metal Powder Forming Processes, Grenoble, France, (1997)277-286.
R.Charlier: "Approche unifiée de quelques problèmes non linéaires de mécanique des milieux continus par la méthode des éléments finis", Ph.D.thesis, Université de LIEGE Faculté des sciences appliquées, BELGIUM, (1987).
P.Mosbah: "Etude expérimentale et modélisation du comportement de poudres métalliques au cours du compactage en matrice fermée", Ph.D.thesis, Université Joseph Fourier, Grenoble, (1995).
P.Mosbah and D.Bouvard: "Finite element simulation of die pressing compaction and ejection of iron powder", Advances in Powder Metall. & Particulate Materials, Vol.2, Part 7, (compiled by T.M.Cadle & K.S.Narasimhan) MPIF, Princeton, (1996)23-37.
O.C.Zienkiewicz: The finite element method, McGraw-Hill Book, (1987).
K.H.Roscoe and J.B.Burland: Engineering Plasticity. Cambridge Univ. Press, (1968)535.
E.Pavier and P.Doremus: "Mechanical behavior of a lubricated iron powder". Advances in Powder Metallurgy and Particulate Material. Vol.2. Part 6. (compiled by T.M.Cadle & K.S.Narasimhan) MPIF. Princeton, (1996)27-40.
P.Mosbah, D.Bouvard. E.Ouedraogo and P.Stutz: "Experimental techniques for analysis of die pressing and ejection of metal powder", Powder Metallurgy. 40 (1997)269-277.
P.Doremus and E.Pavier: "Comparison between constitutive equation modelling the compaction of iron powder and experimental data obtained by triaxial tests", Proc. Int. Workshop on Modelling of Metal Powder Forming Processes. Grenoble, France. (1997)1-8.
P.Mosbah, D.Bouvard, J.Lanier, E.Ouedraogo and P.Stutz: "Rheological characterization of metal powder following various loading paths", Proc. World Congress on Powder Metallurgy, Paris, 1(1994)677-680.
S.Shima and M.A.E.Saleh: "Development of Constitutive Equations for Ceramic Powders Describing Compaction-Induced Anisotropy", Mech. Materials, 16(1993)73-81.
P.Mosbah, J.Kojima, S.Shima and H.Kotera: "Influence of third stress invariant on iron powder behavior during compaction", Proc. Int. Workshop on Modeling of Metal Powder Forming Processes, Grenoble, France, (1997)19-28.
G.Coccoz, M.Bellet, R.Lecot, L.Ackerman and H.-Å Häggblad: "Cold compaction of iron powder: experiments and simulations", Proc. World Congress on Powder Metallurgy, Paris, 1(1994)709-712.
M.Koerner: "Triaxial compaction of metal powder". Powder Metallurgy International, Vol.3. No.4 (1971)86-88.
G.F.Bocchini: "Influence of small die width on filling and compacting densities", Powder Metallurgy, 30 (1987)261-266.
P.Mosbah, S.Shima, A.M.Habraken and R.Charlier: "Numerical simulation of multi-stepped part -A study of influence of kinematics of tooling on powder behavior-", under preparation.
E.Enrst and D.Barnekow: "Pressure, friction and density during axial powder compaction", Proc. World Congress on Powder Metallurgy, Paris, 1(1994)673-676.
K.J.Bathe and A.Chaudhary: "A solution method for planar and axisymmetric contact problems", Int. J. Num. Methids Eng., 21(1985)65-88.
S.Takemoto: "The influence of powder characteristics on slip crack", Advances in Powder Metall. & Particulate Materials, Vol.2, Part 7, (compiled by T.M. Cadle & K.S. Narasimhan) MPIF, Princeton, (1996)87-100.
M.Oldenburg, B.Wikman and H.-Å.Häggblad: "Study of Metal Powder Component Pressing with Use of Numerical Simulations", Proc. World Congress on Powder Metallurgy, Granada, 2(1998)51-56.
