[en] Numerical simulations enable the analysis of the stress and strain histories of bimetallic rolling mill rolls. The history of rolling mill rolls is simulated by thermo-mechanical metallurgical finite element code while considering two steps: post-casting cooling and subsequent tempering heat treatment. The model requires a notably large set of material parameters. For different phases and temperatures, Young modulus, yield limit and tangent plastic modulus are determined through compression tests. Rupture stresses and strains are obtained by tensile tests. Thermo-physical parameters are measured by such experimental methods as dilatometry, DSC (Differential Scanning Calorimetry) and Laser Flash methods. Such parameters as the transformation plasticity coefiicients for the ferrite, pearlite and martensite phases are identified through an inverse method. From the simulation results, the profile of the stresses evolution at different critical times is presented. An analysis of the potential damage is proposed by comparing the predicted axial stress \vith rupture stresses. The perspective of the Ghosh and McClintock damage criteria is also investigated.
Disciplines :
Materials science & engineering
Author, co-author :
Neira Torres, Ingrid
Gilles, Gaëtan ; Université de Liège > Département ArGEnCo > Département Argenco : Secteur MS2F
Tchuindjang, Jérôme Tchoufack ; Université de Liège > Département d'aérospatiale et mécanique > Science des matériaux métalliques
Flores, Paulo
Lecomte-Beckers, Jacqueline ; Université de Liège > Département d'aérospatiale et mécanique > Science des matériaux métalliques
Habraken, Anne ; Université de Liège > Département ArGEnCo > Département ArGEnCo
Language :
English
Title :
FE modeling of the cooling and tempering steps of bimetallic rolling mill rolls
Studer L (2008) Modelling vertical spincasting of large bimetallic rolling mills. DEA thesis. Université de Liège, Belgium
Fu H, Xiao Q, Xing JD (2008) A study on the crack control of a high-speed steel roll fabricated by a centrifugal casting technique. Mater Sci Eng A 474:82–87. doi:10.1016/j.msea.2007.03.101
Gao JW, Wang CY (2000) Modeling the solidification of functionally graded materials by centrifugal casting. Mater Sci Eng A 292:207–215. doi:10.1016/S0921-5093(00)01014-5
Wu SP, Li CY, Guo JJ et al (2006) Numerical simulation and experimental investigation of two filling methods in vertical centrifugal casting. Trans Nonferrous Met Soc China 16:1035–1040. doi:10.1016/S1003-6326(06)60373-7
Mercado-Solis RD, Talamantes-Silva J, Beynon JH, Hernandez-Rodriguez MAL (2007) Modelling surface thermal damage to hot mill rolls. Wear 263:1560–1567. doi:10.1016/j.wear.2006.12.062
Domazet Z, Lukša F, Stanivuk T (2014) An optimal design approach for calibrated rolls with respect to fatigue life. Int J Fatigue 59:50–63. doi:10.1016/j.ijfatigue.2013.09.015
Corral RL, Colás R, Pérez A (2004) Modeling the thermal and thermoelastic responses of work rolls used for hot rolling steel strip. J Mater Process Technol 153–154:886–893. doi:10.1016/j.jmatprotec.2004.04.090
Redkin K, Hrizo C, Mardsen K, et al. (2015) Advanced analytical and non-destructive technologies for engineered roll production. Conf Commun Rolls 5
Ziehenberger K, Windhager M (2005) Recent developments in HSM rougher rolls: risks and chances. Conf Mater Sci Technol
Jin YM, Artemev A, Khachaturyan AG (2001) Three-dimensional phase field model of low-symmetry martensitic transformation in polycrystal: Simulation of ζ’2 martensite in AuCd alloys. 49:2309–2320
Cottura M, Appolaire B, Finel A, Le Bouar Y (2014) Phase field study of acicular growth: role of elasticity in Widmanstätten structure. Acta Mater 72:200–210. doi:10.1016/j.actamat.2014.03.045
Levitas VI (2014) Phase field approach to martensitic phase transformations with large strains and interface stresses. J Mech Phys Solids 70:154–189. doi:10.1016/j.jmps.2014.05.013
Parisier G, Schaffinit P, Steinbach I, Bleck W (2001) Simulation of the γ-α transformation using the phase-field method. Steel Res 72:354–360
Zhu B, Chen H, Militzer M (2015) Phase-field modeling of cyclic phase transformations in low-carbon steels. Comput Mater Sci. doi:10.1016/j.commatsci.2015.01.023
Nakajima K, Apel M, Steinbach I (2006) The role of carbon diffusion in ferrite on the kinetics of cooperative growth of pearlite: a multi-phase field study. Acta Mater 54:3665–3672
Vaks VG, Stroev AY, Urtsev VN, Schmakov AV (2011) Experimental and theoretical study of the formation and growth of pearlite colonies in eutectoid steels. J Exp Theor Phys 112:961–978
Cottura M, Le Bouar Y, Finel A et al (2012) A phase field model incorporating strain gradient viscoplasticity: application to rafting in Ni-base superalloys. J Mech Phys Solids 60:1243–1256
Levitas VI, Lee DW, Preston DL (2010) Interface propagation and microstructure evolution in phase field models of stress-induced martensitic phase transformations. Int J Plast 26:395–422
Geers MGD, Kouznetsova VG, Brekelmans WAM (2010) Multi-scale computational homogenization: trends and challenges. J Comput Appl Math 234:2175–2182
McDowell DL (2010) A perspective on trends in multiscale plasticity. Int J Plast 26:1280–1309
Otsuka T, Brenner R, Bacroix B (2014) FFT-based modelling of transformation plasticity in polycrystalline materials during diffusive phase transformation. Key Eng Mater 622–623:687–697
Lebensohn RA, Kanjarla AK, Eisenlohr P (2012) An elasto-viscoplastic formulation based on fast Fourier transforms for the prediction of micromechanical fields in polycrystalline materials. Int J Plast 32–33:59–69. doi:10.1016/j.ijplas.2011.12.005
Knezevic M, Al-Harbi HF, Kalidindi SR (2009) Crystal plasticity simulations using discrete Fourier transforms. Acta Mater 57:1777–1784. doi:10.1016/j.actamat.2008.12.017
Denis S, Gautier E, Simon A, Beck G (1985) Stress phase transformation interactions—basic principles, modelling and calculation of internal stresses. Mater Sci Technol 1:805–814
Assaker D (1990) Analyse thermomecanique non lineaire par elements finis des traitements thermiques des metaux. PhD thesis. University of Liege, Belgium
Habraken AM, Bourdouxhe M (1992) Coupled thermomechanical- metallurgical analysis during the cooling of steel pieces. Eur J Mech A Solids 11:381–402
Lequesne C (2009) Modeling of fracture in heavy steel welded beam-to-column connection submitted to cyclic loading by finite elments. PhD thesis. Université de Liège, Belgium. http://bictel.ulg.ac.be/ETD-db/collection/available/ULgetd-07062009-125347/
Pascon F (2003) 2D1/2 Thermal-mechanical model of continuous casting of steel using finite element method. PhD thesis. Université de Liège, Belgium. http://bictel.ulg.ac.be/ETD-db/collection/available/ULgetd-06262007-100522/
Schwartz R (2011) Study of the continuous casting of peritectic steel grades by a mesoscopic damage approach. PhD thesis. Université de Liège, Belgium. http://bictel.ulg.ac.be/ETD-db/collection/available/ULgetd-08252011-194757/
Casotto S, Pascon F, Habraken AM, Bruschi S (2005) Thermo-mechanical-metallurgical model to predict geometrical distortions of rings during cooling phase after ring rolling operations. Int J Mach Tools Manuf 657–664
Denis S, Sjostrom S, Simon A (1987) Coupled temperature, stress, phase transformation calculation model numerical illustration of the internal stresses evolution during cooling of an Eutectoid carbon steel cylinder. Metall Trans 18A:1203–1212
Geijselaers HJM (2003) Numerical simulation of stresses due to solid state transformations: the simulations of laser hardening. University of Twente
Li J, Tang L, Li S, Wu X (2013) Finite element simulation of deep cryogenic treatment incorporating transformation kinetics. Mater Des 47:653–666. doi:10.1016/j.matdes.2012.12.076
Lee SJ, Matlock DK, Van Tyne CJ (2013) Comparison of two finite element simulation codes used to model the carburizing of steel. Comput Mater Sci 68:47–54. doi:10.1016/j.commatsci.2012.10.007
Bok HH, Choi J, Barlat F et al (2014) Thermo-mechanical-metallurgical modeling for hot-press forming in consideration of the prior austenite deformation effect. Int J Plast 58:154–183. doi:10.1016/j.ijplas.2013.12.002
Lee CH, Chang KH (2011) Prediction of residual stresses in high strength carbon steel pipe weld considering solid-state phase transformation effects. Comput Struct 89:256–265. doi:10.1016/j.compstruc.2010.10.005
Gurson AL (1977) Continuum theory of ductile rupture by void nucleation and growth: part I—yield criteria and flow rules for porous ductile media. J Eng Mater Technol 99:2. doi:10.1115/1.3443401
Rousselier G, Devaux JC, Mottet G, Devesa G (1989) A methodology for ductile fracture analysis based on damage mechanics: an illustration of local approach of fracture. ASTM Spec Tech Publ 995th ed. 332–354
Lemaitre J (1985) Coupled elasto-plasticity and damage constitutive equations. Comput Methods Appl Mech Eng 51:31–49
Cerri O (2007) Rupture a chaud dans les aciers au cours de leur solidification - caracterisation experimentale et modelisation thermomecanique. PhD thesis. Ecole des mines de Paris
Clift SE, Hartley P et al (1990) Fracture prediction in plastic deformation processes. Int J Mech Sci 32:1–17
Zhu Y, Cescotto S, Habraken AM (1992) A fully coupled elastoplastic damage modeling and fracture criteria in metalforming processes. J Mater Process Technol 32:197–204
Bao Y, Wierzbicki T (2004) On fracture locus in the equivalent strain and stress triaxiality space. Int J Mech Sci 46:81–98. doi:10.1016/j.ijmecsci.2004.02.006
Mae H, Teng X, Bai Y, Wierzbicki T (2008) Comparison of ductile fracture properties of aluminum castings: sand mold vs. metal mold. Int J Solids Struct 45:1430–1444
Bai Y, Wierzbicki T (2008) A new model of metal plasticity and fracture with pressure and Lode dependence. Int J Plast 24:1071–1096. doi:10.1016/j.ijplas.2007.09.004
Basaran M, Wölkerling SD, Feucht M et al (2010) An extension of the GISSMO damage model based on lode angle dependence. LS-DYNA Anwenderforum
El Bartali A, Zhang L, Studer L, Habraken AM (2009) Validation d’un calcul thermique métallurgique in Mécanique et mécanismes des changements de phases. In: Appolaire BA, Chirani S, Calloch S, Denis S, Leal M, Tailleur M, Aussois (eds) MECAMAT 254–258
Neira-Torres I, Gilles G, Tchoufang Tchuindjang J et al (2013) Prediction of residual stresses by FE simulations on bimetallic work rolls during cooling. Comput Methods Mater Sci 13:84–91
Neira-Torres I, Gilles G, Tchoufang Tchuindjang J et al (2014) Study of residual stresses in bimetallic work rolls. Adv Mater Res 996:580–585
Cescotto S, Grober H (1985) Calibration and application of an elastic viscoplastic constitutive equation for steels in hot-rolling conditions. Eng Comput 2:101–106
Johnson WA, Mehl RF (1939) Reaction kinetics in processes of nucleation and growth. Trans AIME Iron Steel Div 135:416
Pumphrey WI, Jones FW (1948) Inter-relation of hardenability and isothermal transformation data. JISI 159:137–144
Koistinen D, Marburger R (1959) A general equation prescribing extent of the austenite-martensite transformation in pure Fe-C alloys and plain carbon steels. Acta Metall 7:59–60
Giusti J (1988) Numerical study of some types of distorsions due to quench of carburized steel pieces. Int Conf Residual Stress 3
Ghosh AK (1976) A criterion for ductile fracture in sheets under biaxial loading. Metall Trans 7a:523–533
McClintock FA, Kaplan SM, Berg CA (1986) Ductile fracture by hole growth in shear bands. Int J Mech Sci 2:614–627
Lecomte-Beckers J, Sinnaeve M, Tchoufang Tchuindjang J (2012) Current developments of alloyed steels for hot strip roughing mills: characterization of high-chromium steel and semi-high speed steel. Iron Steel Technol 33–40
Hwang KC, Lee S, Lee HC (1998) Effects of alloying elements on microstructure and fracture properties of cast high speed steel rolls: Part II. Fracture behavior. Mater Sci Eng A 1–8. doi: 10.1016/S0921-5093(98)00626-1
Tuninetti V (2014) Experimental and numerical study of the quasi-static behavior of Ti-6Al-4V. PhD thesis. Université de Liège, Belgium. http://bictel.ulg.ac.be/ETD-db/collection/available/ULgetd-04252014-163021/
Tuninetti V, Habraken AM (2014) Impact of anisotropy and viscosity to model the mechanical behavior of Ti-6Al-4V alloy. Mater Sci Eng A 605:39–50
Ghaffarian H et al (2015) Molecular dynamics simulation study of the effect of temperature and grain size on the deformation behavior of polycrystalline cementite. Scr Mater 95:23–26
Inoue A, Ogura T, Masumoto T (1977) Microstructures of deformation and fracture of Cementite in Pearlitic carbon steels strained at various temperatures. Metall Trans A 8A:1689–1695
Terashima T, Tomota Y, Isaka M et al (2006) Strength and deformation behavior of bulky cementite synthesized by mechanical milling and plasma-sintering. Scr Mater 54:1925–1929
Meyer L, Weise A, Hahn F (1997) Comparison of constitutive flow curve relations in cold and hot forming. J Phys 4(Fr 07):C3–13–C3–20
Tchoufang Tchuindjang J, Neira Torres I, Flores VP et al (2015) Phase transformations and crack initiation in a high-chromium cast steel under hot compression tests. J Mater Eng Perform 24:2025–2041
Bala P (2009) The kinetics of phase transformation during tempering of tool steels with different carbon content. Arch Metall Mater 54:491–498
Bala P, Pacyna J (2009) The kinetics of phase transformations during continuous heating from as-quenched state in high-speed steels. Arch Mater Sci Eng 37:5–12
Herman M (2006) Etude métallurgique et thermomécanique du phénomène de bris lors de traitements thermiques de cylindres de laminoir en acier moyen chrome. PhD thesis. Université de Liège, Belgium
Coret M (2002) Experimental study of the phase transformation plasticity of 16MND5 steel low carbon steel under multiaxial loading. Int J Plast 18:1707–1727
Denis S, Archambault P, Aubry C et al (1999) Modeling of phase transformations kinetics and coupling with heat treatment residual stress predictions. J Phys 4(Fr 09):323–332
Yanagisawa O, Lui TS (1983) Influence of the structure on the 673 K embrittlement of ferritic spheroidal graphite cast iron. Trans Jpn Inst Metals 24:858–867
Hung-Mao L, Truan-Sheng L, Li-Hui C (2003) Effect of silicon content on intergranular embrittlement of ferritic spheoridal graphite cast iron suffered from cyclic heating. Mater Trans 44:173–180
Tholence F, Norell M (2001) High temperature corrosion of cast irons and cast steels in dry air. Mater Sci Forum 369–372:197–204
Minnebo P, Nilsson K-F, Blagoeva D (2007) Tensile, compression and fracture properties of thick-walled ductile cast iron components. J Mater Eng Perform 16:35–45
Habraken AM (1989) Contribution à la modélisation du formage des métaux par la méthode des éléments finis. PhD thesis. Université de Liège, Belgium. http://bictel.ulg.ac.be/ETD-db/collection/available/ULgetd-12022009-154016/
Otsuka T (2014) Micromechanical modelling of transformation plasticity in steels based on fast Fourier transform numerical scheme. PhD thesis. Paris 13 University, France
