[en] In the framework of the European Joint Programme EURAD, the HITEC work package aimed at investigating the influence of thermal loading on the behaviour of clay-based materials. Three clay formations considered to host potential radioactive waste repositories were studied, the Callovo-Oxfordian (COx) claystone, the Boom Clay and the Opalinus clay as well as different types of bentonite used as engineered barrier. Through HITEC, a series of benchmarking exercises focusing on the clayey host formations were proposed to seven European modelling teams. The benchmark consisted in three consecutive steps, starting with 2D generic models to study the near-field and far-field effects of heating on the behaviour of clay rocks and then considering triaxial compression tests under elevated temperature on COx samples. The last step of the benchmark consisted in modelling two in-situ heating experiments: ALC1605 in the COx claystone and the large scale PRACLAY Heater test in the Boom Clay. In both cases, the teams successfully managed to reproduce the anisotropic response of the clay host rocks to excavation and heating. The evolutions of temperature and pore pressure were well modelled in the far-field with an anisotropic poro-elastic approach but this article highlights particularly how advanced models allowed to capture the processes occurring around the tunnels. In order to match best the measurements, these models required a dependence of the stiffness and permeability with the deformation. One of these advanced models was tested on both in-situ experiments and gave remarkably good results, even though the two clayey host formations have different hydro-mechanical properties. It illustrates a common understanding of THM processes in poorly indurated clay and in claystone and provides some keys for transferring knowledge from one clay formation to another.
Disciplines :
Civil engineering
Author, co-author :
de Lesquen, Christophe; Andra, Châtenay-Malabry, France
Dizier, Arnaud; EURIDICE, Mol, Belgium
Plúa, Carlos; Andra, Châtenay-Malabry, France
Vu, Minh-Ngoc; Andra, Châtenay-Malabry, France
Armand, Gilles; Andra, Châtenay-Malabry, France
Simo, Eric; BGE, Peine, Germany
Vargas, Paola Léon; BGE, Peine, Germany
Raude, Simon; EDF, Palaiseau, France
Tabbal, Ginger El; EDF, Palaiseau, France
Seetharam, Suresh; Belgian Nuclear Research Centre (SCK CEN), Mol, Belgium
Narkuniene, Asta; Lithuanian Energy Institute (LEI), Kaunas, Lithuania
Collin, Frédéric ; Université de Liège - ULiège > Département ArGEnCo
Song, Hangbiao ; Université de Liège - ULiège > Département ArGEnCo > Géotechnique
Gens, Antonio; Universitat Politècnica de Catalunya (UPC), Barcelona, Spain
Song, Fei; Universitat Politècnica de Catalunya (UPC), Barcelona, Spain
The authors would like to thank the EU for funding the research via the EURAD programme and the organising committee of the 9th Clay Conference in Hannover for the opportunity to publish their work.
Armand G Leveau F Nussbaum C de La Vaissiere R Noiret A Jaeggi D Landrein P Righini C Geometry and Properties of the Excavation-Induced Fractures at the Meuse/Haute-Marne URL Drifts Rock Mech Rock Eng 2014 47 21 41 10.1007/s00603-012-0339-6
Armand G Bumbieler F Conil N de La Vaissière R Bosgiraud JM Vu MN Main outcomes from in situ thermo-hydro-mechanical experiments programme to demonstrate feasibility of radioactive high-level waste disposal in the Callovo-Oxfordian claystone J Rock Mech Geotech Eng 2017 9 415 427 10.1016/j.jrmge.2017.03.004
Armand G, Plúa C, Vu M-N 18 years of monitoring pore pressure evolution during and after excavation in the Callovo-Oxfordian claystone: the main insights. 15th ISRM, Congress (2023a) Salzburg, Austria, October 2023
Armand G Plas F Talandier J Dizier A Li XL Levasseur S Contribution of HADES URL to the development of the Cigéo project, the French industrial centre for geological disposal of high-level and long-lived intermediate-level radioactive waste in a deep clay formation Geol Soc Lond Spec Publ 2023 536 237 256 10.1144/SP536-2022-98
Baldi G, Hueckel T, Peano A, Pellegrini R (1991) Developments in Modelling of Thermo-Hydro-Mechanical Behaviour of Boom Clay and Clay Based Buffer Materials. CEC Publishers, Luxembourg, EUR 13365 EN, 3 Vols., 134 pp
Bernier F, Li XL, Bastiaens W, Ortiz L, Van Geet M, Wouters L et al (2007) SELFRAC: fractures and self-healing within the excavation disturbed zone in clays. Final report. EURIDICE Rep
Braun P Delage P Ghabezloo S Chabot B Conil N Vu MN Inducing tensile failure of claystone through thermal pressurization in a novel triaxial device Rock Mech Rock Eng 2022 55 7 3881 3899 1:CAS:528:DC%2BB38XptVGht74%3D 10.1007/s00603-022-02838-3
Brinkgreve RBJ, Kappert MH, Bonnier PG (2007) Hysteretic damping in a small-strain stiffness model. Proc. of Num. Mod. in Geomech., NUMOG X, Rhodes, 737–742
Bumbieler F Plúa C Tourchi S et al. Feasibility of constructing a full-scale radioactive high-level waste disposal cell and characterization of its thermo-hydro-mechanical behavior Int J Rock Mech Min Sci 2021 137 10.1016/j.ijrmms.2020.104555 104555
Bumbieler F Plúa C Vu MN Armand G Assessment of a full-scale in situ heater experiment based on the French high-level waste disposal cell concept conducted in the Callovo-Oxfordian claystone Tunn Undergr Space Technol 2024 153 10.1016/j.tust.2024.106004 106004
Campanella RG Mitchell JK Influence of temperature variations on soil behaviour J ASCE Soil Mech Found Div 1968 94 SM3 709 734 10.1061/JSFEAQ.0001136
Chen GJ Sillen X Verstricht J Li XL ATLAS III in situ heating test in boom clay: Field data, observation and interpretation Comput Geotech 2011 38 683 696 10.1016/j.compgeo.2011.04.001
Chen GJ Li XL Dizier A Verstricht J Sillen X Levasseur S Characterization of boom Clay anisotropic THM behaviour based on two heating tests at different scales in the HADES URL Geol Soc Lond Spec Publ 2023 10.1144/SP536-2022-72
Conil N Vitel M Plúa C Vu MN Seyedi D Armand G In situ investigation of the THM behavior of the Callovo-Oxfordian claystone Rock Mech Rock Eng 2020 53 2747 2769 10.1007/s00603020-02073-8
Cui YJ Sultan N Delage P A thermomechanical model for clays Can Geotech J 2000 37 3 607 620 10.1139/t99-111
De Bruyn D Labat S The second phase of ATLAS: the continuation of a running THM test in the HADES underground research facility at Mol Engineering Geology 2002 64 2–3 309 316 10.1016/S0013-7952(01)00109-0
De Lesquen C et al (2024) Modelling report on the effect of temperature on clay host rocks behaviour. Final version as of 15/04/24 of deliverable 7.6 of the HORIZON 2020 project EURAD. EC Grant agreement N˚ 847593. https://www.ejp-eurad.eu/implementation/influence-temperature-clay-based-material-behaviour-hitec
Dizier A Chen GJ Verstricht J Li XL Sillen X Levasseur S The large-scale in situ PRACLAY heater test: first observations on the in situ thermo-hydro-mechanical behaviour of Boom Clay International Journal of Rock Mechanics and Mining Sciences 2021 137 10.1016/j.ijrmms.2020.104558 104558
Gbewade CAF Grgic D Giraud A et al. Experimental study of the effect of temperature on the mechanical properties of the Callovo-Oxfordian claystone Rock Mech Rock Eng 2024 57 4191 4212 10.1007/s00603-023-03630-7
Hueckel T François B Laloui L Explaining thermal failure in saturated clays Géotechnique 2009 59 3 197 212 10.1680/geot.2009.59.3.197
Li X TIMODAZ: a successful international cooperation project to investigate the thermal impact on the EDZ around a radioactive waste disposal in clay host rocks J Rock Mech Geotech Eng 2013 5 231 242 10.1016/j.jrmge.2013.05.003
Mánica M (2018) Analysis of underground excavations in argillaceous hard soils – weak rocks. PhD thesis, Universitat Politècnica de Catalunya (UPC)
Mánica M Gens A Vaunat J et al. Numerical simulation of underground excavations in an indurated clay using non-local regularisation. Part 1: Formulation and base case Geotechnique 2021 72 12 1092 1112 10.1680/jgeot.20.P.246
Mohajerani M Delage P Sulem J Monfared M Tang AM Gatmiri B A laboratory investigation of thermally induced pore pressures in the Callovo-Oxfordian claystone Int J Rock Mech Min Sci 2012 52 112 121 10.1016/j.ijrmms.2012.02.012
ONDRAF/NIRAS (2020) Design and Construction of the Geological Disposal Facility for Category B and Category C Wastes (V3). Technical Report NIROND-TR 2017-12 E V3. Category B&C. Brussels, Belgium
Ouraga Z Plúa C Vu MN Armand G Thermo-hydro mechanical coupling in a discrete modelling: Large-scale 3D application to thermal hydrofracturing Geomech Energy Environ 2024 41 100656 10.1016/j.gete.2025.100656
Plúa C Vu M-N Armand G Rutqvist J Birkholzer J Xu H Guo R Thatcher K Bond A Wang W Nagel T Shao H Kolditz O A reliable numerical analysis for large-scale modeling of a high-level radioactive waste repository in the Callovo-Oxfordian claystone Int J Rock Mech Min Sci 2021 140 104574 10.1016/j.ijrmms.2020.104574
Plúa C Vu MN de Vaissière L et al. In Situ Thermal Hydrofracturing Behavior of the Callovo-Oxfordian Claystone within the Context of the Deep Geological Disposal of Radioactive Waste in France Rock Mech Rock Eng 2024 57 4265 4283 10.1007/s00603-023-03618-3
Plúa C Vu MN Armand G et al. Numerical investigation of the thermal hydrofracturing behavior of the Callovo-Oxfordian claystone Geomech Energy Environ 2024 40 100596 10.1016/j.gete.2024.100596
Rice JR Heating and Weakening of Faults during Earthquake Slip J Phys Res 2006 111 B05311 10.1029/2005JB004006
Seyedi DM, Plúa C, Vitel M, Armand G, Rutqvist J, Birkholzer J, Xu H, Guo R, Thatcher KE, Bond AE, Wang W, Nagel T, Shao H, Kolditz O (2021) Upscaling THM modeling from small-scale to full-scale in-situ experiments in the Callovo-Oxfordian claystone. Int J Rock Mech Min Sci 144. https://doi.org/10.1016/j.ijrmms.2020.104582
Shao JF Yu Z Vu MN Multiscale modeling of thermo-hydromechanical behavior of clayey rocks and application to geological disposal of radioactive waste J Rock Mech Geotech Eng 2025 17 1 1 19 10.1016/j.jrmge.2024.11.008
Simo E et al. THM-Modelling Benchmark Initiative on the Effects of Temperature on the Disposal of Heat-Generating Radioactive Waste in Clay Formations Acta Geotech 2025 20 1621 1642 10.1007/s11440-024-02502-w
Simo E et al (2025b) Benchmarking thermo-hydro-mechanical models for geological barrier integrity in clay-based repositories. Acta Geotech 1–19. https://doi.org/10.1007/s11440-025-02683-y
Song H (2025) Thermo-Hydro-Mechanical Behaviour of the Argillaceous Rock in the Context of Nuclear Waste Repository [Doctoral thesis, ULiège - Université de Liège]. https://orbi.uliege.be/handle/2268/334366
Song H, Dizier A, Levasseur S, Seetharam S, Collin F (2025) A stress- and strain-dependent constitutive modelling of the large-scale in situ PRACLAY heater test. Comput Geotech 186. https://doi.org/10.1016/j.compgeo.2025.107365
Souley M, De Lesquen C, Vu MN, Armand G (2026) Advanced thermo-hydro-mechanical modelling of Callovo-Oxfordian claystone: Temperature effects and multi-scale applications for geological disposal safety. Int J Rock Mech Min Sci 199. https://doi.org/10.1016/j.ijrmms.2026.106397
Tourchi S Vaunat J Gens A Bumbieler F Vu MN Armand G A full-scale in situ heating test in Callovo-Oxfordian claystone: observations, analysis and interpretation Comput Geotech 2021 133 104045 10.1016/j.compgeo.2021.104045
Tourchi S, Mánica MA, Gens A, Vaunat J, Vu MN, Armand G (2023) A thermomechanical model for argillaceous hard soils–weak rocks: application to THM simulation of deep excavations in claystone. https://doi.org/10.1680/jgeot.23.00023. Géotechnique
Tsang CF Bernier F Davies C Geohydromechanical processes in the excavation damaged zone in crystalline rock, rock salt, and indurated and plastic clays—in the context of radioactive waste disposal Int J Rock Mech Min Sci 2005 42 1 109 125 10.1016/j.ijrmms.2004.08.003
Verstricht, J, Nackaerts D, Li XL, Leonard D, Levasseur S, Van Geet M (2023) Assessment of long-term sensor performance based on a large THM experiment in the HADES URL, Geological Society of London. https://doi.org/10.1144/SP536-2022-87
Villar MV, Armand G, Conil N, de Lesquen C, Herold P, Simo E, Mayor JC, Dizier A, Li X, Chen G, Leupin O, Niskanen M, Bailey M, Thompson S, Svensson D, Sellin P, Hausmannova L (2020) D7.1 HITEC. Initial State-of-the-Art on THM behaviour of i) Buffer clay materials and of ii) Host clay materials. Deliverable D7.1 HITEC. EURAD Project, Horizon 2020 No 847593. 214 pp
Villar MV Bésuelle P Collin F Cuss R de Lesquen C Dizier A El Tabbal G Gens A Graham C Grgic D Harrington J Imbert C Leupin O Levasseur S Narkūnienė A Simo E Tatomir A-B EURAD state-of-the-art report: thermo-hydro-mechanical behaviour at high temperature of host clay formations Front Nucl Eng 2025 4 1436490 10.3389/fnuen.2025.1436490
Vu MN Armand G Plúa C Thermal pressurization coefficient of anisotropic elastic porous media Rock Mech Rock Eng 2020 53 2027 2037 10.1007/s00603-019-02021-1
Vu MN Guayacán-Carrillo LM Armand Excavation induced over pore pressure around drifts in the Callovo-Oxfordian claystone Eur J Environ Civil Eng 2020 27 8 2614 2629 10.1080/19648189.2020.1784800
Vu MN, Plúa C, Armand G, Bumbieler F, De Lesquen C, Souley M, Alonso M, Vaunat J, Gens A, Yu Z, Shao JF (2025) Thermo-hydro-mechanical responses of a high-level radioactive waste repository: Effects of short- and long-term nonlinear behavior of the host rock. Int J Rock Mech Min Sci 195. https://doi.org/10.1016/j.ijrmms.2025.106281
Wileveau Y, Cornet FH, Desroches J, Blumling P (2007) Complete in situ stress determination in an argillite sedimentary formation. Phys Chem Earth 32:866–878. https://doi.org/10.1016/j.pce.2006.03.018
Yu Z Shao J Vu MN Armand G Numerical study of thermo-hydro-mechanical responses of in situ heating test with phase-field model Int J Rock Mech Min Sci 2021 138 104542 10.1016/j.ijrmms.2020.104542
